The first thing to keep in mind, when you first initialize(setup) your NAS, is to NOT allocated 100% of storage space. Here is a QTS 4.3.4 video for people not familiar with QNAP QTS OS.įrom However i will mention my experiences with snapshots which i'm pretty new to, since this is the first time i actively used snapshots. it can also do all the usual stuff a QNAP does via QTS, so i won't get too much into that. Emby client force sterio torrent#because of the good hardware specs, there are a lot of things you can do with this NAS, and not just with QPKGs from appcenter, but also using container station to use other apps available from docker I tested using transmission torrent client and it worked I can setup a torrent seedbox this way if i wanted to. i got a low profile graphics just in case. for graphics dimensions i found this image. I'm not sure whether 1060 needs to plug in the power cable or not. You may be interested to know that, though there are power cables available to power the graphics, the 1050 i used didn't require using it, as just installing the pcie slot was sufficient. A 1060 TI would probably be better but i wanted to spend as least as possible, as this is a feature i don't use too frequently. I tested so far using a Nvidia 1050 AERO ITX 2gb vram. Then go to qts > hardware and enable the toggle for VM or transcoding mode (reboot is required if you switch between modes). Emby client force sterio install#tested transcoding using qnap video station To utilize graphics you need to first install the graphics card. but seems to work only for qnap native app hdstation and video station. graphics card can also be used for transcoding acceleration. I found that VM rollback using snapshots works excellently so can play around without worry as i can reset back to a clean slate. anyway i can test apps before applying to my own desktop workstation. This setup is probably most practical for me since like i mentioned earlier why i can't use HDMI. I recommend using this video guide which i used to do the same.įrom Alternatively you can setup to access the qnap VM via network rather than HDMI (though you cannot make use of the graphics card that way as far as i tried). VM won't have the same performance as bare metal, but it can get close by doing further optimization when setting up VM. You basically turn the qnap into a desktop workstation doing that. to use the graphics card, you must plug the qnap via HDMI to a monitor though if you intend to utilize the graphics card. Emby client force sterio driver#I used virtual station from app center, to setup win10 and using virtio driver for hdd performance. another thing i tried was VM (which is probably one of the major reasons to get this series). but for best performance plugging qnap direct using hdmi would probably work best. i still get to use kodi minus needing to use the qnap hdmi. Emby client force sterio android#unfortunately i don't use this because requires plugging to HDMI which i can't because i move my qnap to router which is no where near my HDTV Instead i use a Himedia h8 android box (which has kodi installed) DLNA to access the qnap. I also tested my Aktimate Mini speakers plugged into the qnap, and the audio played through it hdplay is nice but using the Kodi (provided by father mande) works the best. I prefer best Kodi for HDTV, though i wouldn't mind plex or emby (since they don't require me to use HDMI at all) also tested hdstation, works. I still prefer watching on desktop via MPC HC (lav megamix), but i wouldn't mind the quality on Emby or plex, though i'd probably use them for remote access or when watching on mobile devices. blueray rip mkv to get an idea what i see on screen. plex test emby test did a screencap for a better quality screenshot for emby playback transcoding. Emby client force sterio 1080p#for Plex i set hurt cpu, though i preferred setting it to the setting just below that for smoothest playback (especially for my 1080p high bit rate video content and hevc) quality. Note that in 4.3.4 the HDD order does not matter when doing NAS migration (in 4.3.3 it does ) Plex and Emby works. But i later reinitialized again to start from scratch (after i tested nas migration works), then used hybrid backup sync to restore from my backup qnap NAS to the new one. details added here I did test the old (ts-653a) to new NAS (ts-877) migration and it worked (turn off both units, then remove hdd and put into new unit, then boot up, and your data is still intact).
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |